Device and Network for the Franklin Wireless R702Router Sceenshot

Back to the Franklin Wireless R702



Screenshots from PortForward.com


Smart 4G LTE USB Modem --> 4G LTE Portable Wi-Fi Hotspot The webpage will refresh because the system may be rebooted. Your Franklin Connection Manager has determined that 3G will provide the best connection at this time. Do you want to connect to 3G now?   DO NOT REMOVE YOUR USB DEVICE FROM THE COMPUTER WHILE THIS MESSAGE IS DISPLAYED Important Notice: Your USB device is applying new software or service settings. This may take a few minutes. It is very important that the device remain in the computer's USB port during this operation. It is best to plug your computer into a wall outlet at this time to reduce the risk of losing power during this operation. Network Logon Credentials Enter username and password that will be used to logon on to your network. Username Password Network Logon Credentials Enter username and password that will be used to logon on to your network. Username (Permanently Stored) " readonly> Password Network Logon Credentials Enter username and password that will be used to logon on to your network. Username (Permanently Stored) Network Logon Credentials Enter username and password that will be used to logon on to your network. Username (Permanently Stored) Password (Permanently Stored) Information Please wait until NMEA is enabled. Message screen will close automatically after NMEA is enabled. NOTE: If the NMEA driver does not automatically install, please proceed to the FranklinCD drive under My Computer for manual install.     Fail to NMEA Please wait until NMEA is . This message will close automatically. NMEA is only supported on Windows. Datalink will be enabled and webpage will be reload !! Continue?   Please wait until switching is completed. Handover to better service... Battery level is low. Please charge the battery more than 50% and try again. SW update is available. Would you like to download now?     Please wait until IPPT is enabled. This message will close automatically. Please wait until IPPT is disabled. This message will close automatically. Fail to IPPT As IPPT is Enabled, your web connection will be lost for a few seconds. This message will close automatically. Datalink will be disabled and webpage will be reload !! Continue?   Currently data is connected, or 3G radio is off. do you want to disconnect or turn 3G radio on and proceed?   Airplane mode is enabled. Please try again after unchecking "Enable Airplane Mode". Currently data is not connected. Please try to connect the network! Please wait ... --> Scanning for networks. Please wait... You are about to establish a data connection on a roaming network within the U.S., Puerto Rico, and U.S. Virgin Islands. Roaming charges may apply per your service plan options. Certain data usage limits apply per your service plan agreement.   You are about to establish a data connection on an internatinal roaming network outside the U.S., Puerto Rico, and U.S. Virgin Islands. International roaming charges apply per your service plan options. Certain data usage limits apply per your service plan agreement.   You currently do not have International Roaming enabled. Please make sure you have International setup on your account and the Hostless CM. There was a problem trying to connect. Please retry. If the problem persists, contact Customer Support Center.   There was a problem trying to connect. Please retry. If the problem persists, contact Customer Support Center.   There was a problem trying to connect to the network. If you have an active device account, please retry. If this is a recycled device, has previously been activated, or used with a Day Pass, press Reset. If the problem persists, contact Customer Support Center.     There was a problem trying to connect to the network. If you have an active device account, please retry. If this is a recycled device, has previously been activated, or used with a Day Pass, press Reset. If the problem persists, contact Customer Support Center.     Administrator Login Required This operation will restore all settings back to factory default, continue?   MSL code required      Sorry, the MSL is incorrect. Please try again. The device is now rebooting... Reconnect to the WiFi hotspot and refresh your browser after the device reboots. The device is now rebooting... Reconnect to the WiFi hotspot and refresh your browser after the device reboots. The DSA transaction has been completed successfully. The 3G device is now rebooting, You will be redirected back to the system after  seconds. Connecting to activation server... If you have connection issues, please hit refresh on your browser or return back to Web UI and try again. If your connection fails again, please call Customer Support Center. You have lost your connection to the network. Please retry to establish connectivity and continue with your activation. If your connection fails again, please call Customer Support Center. The restore process has completed successfully. The device is now rebooting. You will be redirected momentarily. Your device is now rebooting. You will be redirected momentarily. Please wait ... Activation Information Service is not activated Service is activated Activation is not available in 4G LTE network. If you want to activate the device, please change the connection mode to 3G Only! Network does not respond Service is already activated Activation is not completed Error : Password length is 0 ! Try it again! Sorry, the PIN code is incorrect. Please try again. Sorry, PIN retries is exceeded or incorrect Please try again. Searching... This may take a few moments. Connection Options will change to '3G Only' mode. Connection Options will change to '2G Only' mode. Connection Options will change to '4G LTE Only' mode. Currently data is connected. Please try to disconnect the network! Smilecoms 4G LTE Portable Wi-Fi Hotspot Would you like to log out now?   English Español Francais Русский Portugues 한국어 --> Administrator Administrator (Default password: admin)   4G END-->     --> Hide Networks 4G LTE 3G --> Enter PIN code   Enter PUK code Enter New PIN code   Enter New PIN code   Do you want to install Firmware now?   Do you want to install Firmware now?   Activation in progress. Press OK to continue. PRL has been updated. Press OK to continue. Do you want to install Firmware now?   Device has been activated! Press OK to continue. -->
Home > Screenshots > Franklin Wireless > R702 > Device and Network