Connection Basic for the TP-Link TL-WR1043N v2 - KiboshRouter Sceenshot

Back to the TP-Link TL-WR1043N v2 - Kibosh



Screenshots from PortForward.com


Kibosh Router Management Utility Please Wait While Settings Are Applied Kibosh Router Management Utility Device Name: sparkle Device Configuration Configure Device As: Gateway (Default) Wireless Bridge/Repeater Wireless Bridge/Repeater Bridge IP: (must be in AP subnet) Subnet Mask: (same as AP mask) AP/Gateway IP: Wan Ethernet Port: Disable Bridge To LAN DNS Servers: Use Gateway As DNS Server Custom DNS Server(s) Connect Via Client Bridge Connect Via WDS Repeater: Repeater Enabled Repeater Disabled Operation Mode: N+G+B G+B B auto Channel Width: 20MHz 40MHz (2nd chan. above) 40Mhz (2nd chan. below) Transmit Power: Max Custom   dBm Channel Width: 20MHz 40MHz (2nd chan. above) 40MHz (2nd chan. below) Transmit Power: Max Custom   dBm SSID to Join: Other SSID to Join: SSID to Broadcast: Wireless Channel: auto 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Wireless Channel: Wireless Channel:   Encryption: None WPA2 PSK WPA PSK WEP Encryption:   Password: WEP Hex Key: MAC Of This Device: Other WDS MAC Addresses: Internet / WAN Connect Via: DHCP (Wired) PPPoE (Wired) Static IP (Wired) DHCP (Wireless) Static IP (Wireless) 3G (GSM) Disabled Current IP: Current Lease Expires: User Name: Password: Reconnect Mode: Connect On Demand Keep Alive Max Idle Time: (minutes) Failed Pings Before Reconnect: Ping Interval: (seconds) Static IP: Subnet Mask: Gateway: Service: CDMA/EV-DO 4G/3G/2G (auto) 3G Preferred 2G Preferred 3G Only 2G Only Device: Pincode: (optional) Mobile ISP: Custom APN: User Name: (optional) Password: (optional) Wan Ethernet Port: Disable Bridge To LAN Use Custom MAC Address:    Use Custom MTU:      Drop Ping From WAN Side Local Network / LAN Router IP: Subnet Mask: Gateway: KRMU ID: Wireless Wireless Mode: Access Point (AP) AP+WDS Client Client+AP Ad Hoc Disabled Operation Mode: N+G+B G+B B auto Channel Width: 20MHz 40MHz (2nd chan. above) 40MHz (2nd chan. below) Transmit Power: Max Custom   dBm 5GHz Channel Width: 20MHz 40MHz (2nd chan. above) 40MHz (2nd chan. below) 5GHz Transmit Power: Max Custom   dBm Wireless MAC Filter: Disabled Enabled MAC filtering applies to all wireless interfaces, including those in client mode. In client mode you must be sure to allow the MAC address of the AP to which you are connected. MAC Filter Policy: Allow Only MACs Listed Below Deny Only MACs Listed Below SSID to Join: Other SSID: Wireless Band: 2.4 GHz 5 GHz Wireless Channel: auto 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Wireless Channel:   Wireless Channel: Encryption: None WPA2 PSK WPA PSK WEP Encryption:   Password:    reveal WEP Hex Key: Access Point SSID: AP 5GHz SSID: Wireless Channel: auto 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Wireless Channel:   Wireless Channel (5GHz): Encryption: None WPA2 PSK WPA PSK WEP WPA RADIUS WPA2 RADIUS Password:    reveal WEP Hex Key: RADIUS Server IP: RADIUS Server Port: Broadcast SSID: Disabled Enabled Wireless Client Isolation: Disabled Enabled MAC Of This Device: Other WDS MAC Addresses: --> Status Overview Bandwidth Usage B/W Distribution Web Usage Connected Hosts Connection List Connection Basic DHCP Web Filter Bypass Web Filter Settings Routing Wake on LAN Firewall Port Forwarding Connection Limits Restrictions Domain Blocking Quotas QoS (Upload) QoS (Download) System Router Access Identification Time USB Storage USB Printer Net Schedule WiFi Schedule Backup / Restore Update Firmware Reboot Router Manual About Logout
Home > Screenshots > TP-Link > TL-WR1043N v2 - Kibosh > Connection Basic